Starting generation of Calibration File 
FS version = 0009.0009.0002 
time_zero = 14400000 
Found #306 errors of type = ERROR qk -211 Tsys value for device i2 overflowed or was less than zero. 
Found #273 errors of type = ERROR qk -211 Tsys value for device v2 overflowed or was less than zero. 
Found #44 errors of type = ERROR m5 -104 mk5cn: time-out on mk5 device  connection closed 
Found #32 errors of type = ERROR qk -211 Tsys value for device i1 overflowed or was less than zero. 
Found #14 errors of type = ERROR qk -211 Tsys value for device vc overflowed or was less than zero. 
Found #11 errors of type = ERROR ch -317 Total power integrator overflow on IF2 
Found #11 errors of type = ERROR st -204 WARNING: not OK to move the antenna! No R commands will be sent.
 
Found #10 errors of type = ERROR qk -211 Tsys value for device v9 overflowed or was less than zero. 
Found #7 errors of type = ERROR m5  -21 mk5cn: error connect(): mk5 device connection open timed-out 
Found #7 errors of type = ERROR ch -349 The Receiver 70K stage is hotter than  65K. 
Found #7 errors of type = ERROR ch -350 The Receiver 20K stage is hotter than  40K. 
Found #6 errors of type = ERROR ch -309 v5 alarm is on 
Found #5 errors of type = ERROR ch -316 Total power integrator overflow on IF1 
Found #5 errors of type = ERROR ch   -4 Device v5 timed-out on response from MATCN 
Found #4 errors of type = ERROR ch -309 v6 alarm is on 
Found #3 errors of type = ERROR sp   -4 Unrecognized name (not a function or procedure). 
Found #2 errors of type = ERROR ch -301 v5 module is not in remote 
Found #2 errors of type = ERROR ch -304 v2 TPI selection does not check with requested setting 
Found #2 errors of type = ERROR ch -306 v2 LSB attenuator does not check with requested setting 
Found #2 errors of type = ERROR ch -309 v2 alarm is on 
Found #2 errors of type = ERROR qk -211 Tsys value for device va overflowed or was less than zero. 
Found #2 errors of type = ERROR ch   -4 Device v2 timed-out on response from MATCN 
Found #2 errors of type = ERROR ch -303 v5 bandwidth does not check with requested value 
Found #2 errors of type = ERROR ch -303 v2 bandwidth does not check with requested value 
Found #2 errors of type = ERROR an -103 Pointing computer tracking errors are too large. 
Found #2 errors of type = ERROR ch -305 v2 USB attenuator does not check with requested setting 
Found #2 errors of type = ERROR qo -301 WARNING: ONSOURCE status is SLEWING! 
Found #2 errors of type = ERROR ch -302 v2 frequency does not check with requested value 
Found #1 errors of type = ERROR ch -306 v5 LSB attenuator does not check with requested setting 
Found #1 errors of type = ERROR ch   -4 Device v6 timed-out on response from MATCN 
Found #1 errors of type = ERROR ch -302 v5 frequency does not check with requested value 
Found #1 errors of type = ERROR ch -302 v6 frequency does not check with requested value 
Found #1 errors of type = ERROR ch -304 v5 TPI selection does not check with requested setting 
Found #1 errors of type = ERROR ch -305 v5 USB attenuator does not check with requested setting 
Found #1 errors of type = ERROR ch -305 v6 USB attenuator does not check with requested setting 
Found #1 errors of type = ERROR un  115 Operation now in progress 
Found #1 errors of type = ERROR ch -307 v2 unlock indicator is on 
Found #1 errors of type = ERROR ch -307 v5 unlock indicator is on 
Found #1 errors of type = ERROR ch -303 v6 bandwidth does not check with requested value 
Found #1 errors of type = ERROR ch -307 v6 unlock indicator is on 
Found #1 errors of type = ERROR ch -304 v6 TPI selection does not check with requested setting 
Found #1 errors of type = ERROR m5  -23 mk5cn: socket open error from getsockopt() 
Found #1 errors of type = ERROR ch -306 v6 LSB attenuator does not check with requested setting 
Found these BBCs: vc01 vc05 vc09
NBBC: 3
Found these RX parameters: 02(LO) 03(DCAL) 05(INLET)
RX1 min= 41.87 max= 50.32
RX2 min= 39.15 max= 47.74
RX3 min= 30.42 max= 39.30
Plotting 3 Tsys channels: 01 05 09
Tsys values are: 1 2 3 etc
NTSYS: 3
in match_chan ft1= r1383ft.log.tsy1.ntup nt1= 7 st1= 1d tt= 1
set scale tsys1 [2] min max 181.9 290.3
set scale tsys2 [2] min max  
set scale tsys3 [2] min max  
set scale tsys4 [2] min max  
 Tsys scale ymin 188.2 ymax 305 
in match_chan ft1= r1383ft.log.tsy1.ntup nt1= 19 st1= 5u tt= 1
set scale tsys1 [2] min max 181.9 290.3
set scale tsys2 [2] min max  
set scale tsys3 [2] min max  
set scale tsys4 [2] min max  
 Tsys scale ymin 185.1 ymax 271.4 
in match_chan ft1= r1383ft.log.tsy1.ntup nt1= 12 st1= 9u tt= 1
set scale tsys1 [2] min max 181.9 290.3
set scale tsys2 [2] min max  
set scale tsys3 [2] min max  
set scale tsys4 [2] min max  
 Tsys scale ymin 41 ymax 305