Starting generation of Calibration File 
FS version = 0009.0007.0007 
time_zero = 9907200 
Found #324 errors of type = ERROR qk -211 Tsys value for device v9 overflowed or was less than zero. 
Found #302 errors of type = ERROR ch -308 v9 total power integrator overflow 
Found #173 errors of type = ERROR st  -14 Antenna stuck.
 
Found #10 errors of type = ERROR an -103 Pointing computer tracking errors are too large. 
Found #10 errors of type = ERROR qo -301 WARNING: ONSOURCE status is SLEWING! 
Found #6 errors of type = ERROR ch   -4 Device v9 timed-out on response from MATCN 
Found #4 errors of type = ERROR ch -317 Total power integrator overflow on IF2 
Found #4 errors of type = ERROR qk -211 Tsys value for device i2 overflowed or was less than zero. 
Found #2 errors of type = ERROR qk -211 Tsys value for device vd overflowed or was less than zero. 
Found #2 errors of type = ERROR qk -211 Tsys value for device vc overflowed or was less than zero. 
Found #2 errors of type = ERROR qk -211 Tsys value for device ve overflowed or was less than zero. 
Found #2 errors of type = ERROR ch -309 v9 alarm is on 
Found #2 errors of type = ERROR sp   -4 Unrecognized name (not a function or procedure). 
Found #1 errors of type = ERROR ch -304 v9 TPI selection does not check with requested setting 
Found #1 errors of type = ERROR ch -305 v9 USB attenuator does not check with requested setting 
Found #1 errors of type = ERROR ch -350 The Receiver 20K stage is hotter than  40K. 
Found #1 errors of type = ERROR ch -303 v9 bandwidth does not check with requested value 
Found #1 errors of type = ERROR ch -306 v9 LSB attenuator does not check with requested setting 
Found #1 errors of type = ERROR ch -307 v9 unlock indicator is on 
Found #1 errors of type = ERROR ch -302 v9 frequency does not check with requested value 
Found #1 errors of type = ERROR ch -349 The Receiver 70K stage is hotter than  65K. 
Found these BBCs: vc01 vc05 vc09
NBBC: 3
Found these RX parameters: 02(LO) 03(DCAL) 0E(LO5MHZ)
RX1 min= 43.04 max= 45.23
RX2 min= 38.88 max= 40.72
RX3 min= 0.145 max= 0.147
Plotting 3 Tsys channels: 01 05 09
Tsys values are: 1 2 3 etc
NTSYS: 3
in match_chan ft1= r1221ft.log.tsy1.ntup nt1= 7 st1= 1d tt= 1
set scale tsys1 [2] min max 79.4 207.3
set scale tsys2 [2] min max  
set scale tsys3 [2] min max  
set scale tsys4 [2] min max  
 Tsys scale ymin 72.4 ymax 208.8 
in match_chan ft1= r1221ft.log.tsy1.ntup nt1= 19 st1= 5u tt= 1
set scale tsys1 [2] min max 79.4 207.3
set scale tsys2 [2] min max  
set scale tsys3 [2] min max  
set scale tsys4 [2] min max  
 Tsys scale ymin 75.1 ymax 196.6 
in match_chan ft1= r1221ft.log.tsy1.ntup nt1= 12 st1= 9u tt= 1
set scale tsys1 [2] min max 79.4 207.3
set scale tsys2 [2] min max  
set scale tsys3 [2] min max  
set scale tsys4 [2] min max  
 Tsys scale ymin -5 ymax 305