IVS-R1007 (International VLBI Services-Rapid Turnaround 1007) 2002 February 19 Notes prepared by Cynthia Thomas and Nancy Vandenberg,NVI/GSFC Session code: r1007 Schedule file: feb02/r1007.skd on CDDISA Nominal Start: 17:00 U.T. on February 19 (day 050) first observation at 17:00 U.T. on 0552+398 Nominal Stop: 17:00 U.T. on February 20 (day 051) last observation at 16:45 U.T. on 0727-115 for HH-TS last observation at 16:48 U.T. on 2234+282 for GC-MA-WF-WZ Correlator: Bonn 1 letter 2 letter Station Code Code # of tapes # of obs Fairbanks A GC 2 (TT) 527 HartRAO J HH 1 (TT) 174 Matera I MA 2 (TT) 464 Tsukuba T TS 2 (TT) 466 Westford E WF 2 (TT) 408 Wettzell V WZ 2 (TT) 525 Purpose ======= This information is located at http://ivscc.gsfc.nasa.gov/program/descrip2002.html#r1. Observing Mode ============== CORE Mode "4F" (four times the standard mode C, fanned out with barrel roll) ----------------------------------------------------------------- Number of frequencies 14 Frequency sequence X-band standard wide-band frequency sequence modified to avoid RFI at Matera S-band NEW sequence to avoid overlapping channels at the high end Number of channels 16 (14 USB + 2 LSB) Channel bandwidth 8.0 MHz Sample rate 16 Mb/s Bits per sample 1 Total data rate 256 Mb/s Data rate on tape 8 Mb/s/track Fan-out 1:2 Tape speed 160 ips Tracks per pass 32 Passes per tape 14 Barrel roll yes for Fairbanks (*) Track frame format Mark4 and VLBA (*) The 16 recorded channels are comprised of a 14-channel USB frequency sequence plus the LSB channels of the first and last frequencies at X-band. The two outer X-band LSB channels give extra sensitivity. They also slightly narrow the peak of the delay resolution function, resulting in better group delay precision. This session uses a NEW S-BAND FREQUENCY SEQUENCE, generated by Dave Shaffer. Because of the 8 MHz channel bandwidth, the standard S-band sequence had some overlapping channels. This sequence avoids the overlap and tries to avoid the direct-broadcast satellite band of 2320-2345 MHz. (*) Fairbanks, which has a VLBA backend, will use barrel roll during this session and record in VLBA (non-data replacement) format. Stations with Mark 4 formatters cannot barrel roll. Schedule ======== This schedule was made by C. Thomas using sked. Schedule setup parameters: Early start 10 sec Minimum scan length 30 sec Maximum scan length 180 sec* Minimum SNR 20 at X-band 15 at S-band * The maximum scan length was reduced to 180 seconds so that more scans would be scheduled using less tapes. The IVS-R1 sessions were planned with the stations utilizing no more than two (2) tapes per session. Automatic scheduling setup: optimize for uniform sky coverage at all stations, maximize the number of observations, minimize slewing time, minimize time between scans, consider the top 50% of ranked scans for selection, consider the last 1 hour of scans for sky coverage calculations, minimum 50 min between scans on the same source. The characteristics of the generated schedule are listed below. These will vary slightly for each schedule that is generated. Schedule characteristics: Average scan length 51 seconds Median SNR 40.0 at X-band 30.0 at S-band Number of observations 3215 observations Average scans per station 427 scans Parity ====== This schedule was made with a minimum scan time of less than the 55 seconds required for parity checks. As a result, some parity checks in the schedule may give bad results even though there is nothing wrong. The next release of the FS, 9.5, will correct this problem. In the meantime, please check when a parity check fails to see if the cause is a short scan. If the problem is presistent and occurs frequently at your station for a given schedule type, you may want to disable parity checks for specific experiments of that type. You can do this by creating empty "checkf80" and "checkr80" procedures (or "checkf135" and "checkr135" if you are using thick tape) in the EXPERIMENT procedure library for the effected experiment. If you do this, it is strongly recommend that you verify recorder performance before the experiment by recording some tape in both directions using the experiment set-up and check it with the appropriate parity check procedures. Flux Information ================ The flux catalog, flux.jan02.cat, was used in preparing this schedule file. The flux catalog is located at gemini:/home/ftp/pub/sked/catalogs. SKED Summary from file ./r1007.skd for experiment R1007 (all scans with at least one subnet station) Average number of obs. per baseline per source (normalized by up-time) = 7.4 Min = .0 Max = 28.6 (Baseline Gc-Ts on 0727-115) RMS = 7.7 Total time: 1429 minutes ( 23.8 hours). Key: Gc=GILCREEK Hh=HARTRAO Ma=MATERA Ts=TSUKUB32 Wf=WESTFORD Wz=WETTZELL Gc Hh Ma Ts Wf Wz Avg % obs. time: 29 11 28 25 28 29 25 % cal. time: 6 2 5 5 4 6 4 % slew time: 33 36 34 22 20 19 27 % idle time: 30 49 31 46 46 44 41 # of tapes : 1.7 .7 1.6 1.5 1.6 1.8 total # scans: 527 174 464 466 408 525 427 # scans/hour : 22 7 19 19 17 22 17.8 Avg scan (sec): 48 58 51 47 59 48 51 # OF OBSERVATIONS BY BASELINE | Gc Hh Ma Ts Wf Wz StnTotal -------------------------------------- Gc|527 13 206 383 316 287 1205 Hh| 174 154 54 44 140 405 Ma| 464 208 242 438 1248 Ts| 466 188 258 1091 Wf| 408 284 1074 Wz| 525 1407 Number of 2-station scans: 272 Number of 3-station scans: 242 Number of 4-station scans: 187 Number of 5-station scans: 108 Number of 6-station scans: 1 Total # of scans, observations: 810 3215 Average baseline components for all observations Average XY = 5534. Average XZ = 4862. Average YZ = 4165. Average length = 6275.